Mira Escape Guia do Utilizador

1These instructions are to be left with the userInstallation & User GuideMira Escape Thermostatic Electric Shower

10Double-poleIsolating SwitchConsumer UnitInstallationInstallation of Mira EscapeWarning! Turn off the electrical and water supplies before proceeding

11Three case inserts are supplied with the Mira Escape, so that they can be trimmed to suit the supplies entering the product. Before tting the cover

12Feed cable into Case. Fit Earth sleeve (not supplied) and strip insulation.Do not twist cable cores.Firmly connect the conductors. Do not exert stra

13Cold Water Supply Pipe (Bottom Entry)Service TunnelFixing ScrewHoles For CoverRetaining ScrewsCase InsertElectrical Supply CableTerminal BlockInlet

14CommissioningTurn control to full cold. Turn the water supply fully on.Check for water leaks. Set control to ‘I’. S w i t c h o n e le c t r

15Turn control to full cold. The temperature will rise slightly.Set control to ‘II’.0 - 10 Secs12.11.10.The temperature will rise further.A d j u s

16The warmer the shower, the lower the ow rate and vice versa.Heated water is produced by adjusting the ow of cold water passed through a heater tan

17Water inlet pressure uctuations due to other draw offs (e.g. ushing toilet). Shower temperature will be controlled to within ± 2°C of the set temp

18Using your ShowerRead the section “Important Safety Information” rst.Note! At the end of every shower make sure that the shower head points into th

19Fault DiagnosisThe trouble shooting information tabled below gives details on probable causes and remedies should difculties be encountered whilst

2ContentsIntroduction ...3Patents and Design Registration ..

20Symptom Power LightLow Flow LightHeater Setting I/II/IIIProbable Cause Possible RemedyL o w o r n o ow.ON ON ON ONON ONONON ON

21Symptom Power LightLow Flow LightHeater Setting I/II/IIIProbable Cause Possible RemedyWater will not turn off.ON ONOFF ONAny AnyInlet valve, sol

22Make sure that the electrical supply is turned off at the mains and that the water supply is fully turned off.Remove the three screws, the

23FilterHold a wrench across the ats of the metal connector. Unscrew the filter using another wrench as shown. Clean or renew the Filter as neces

24Spare PartsMira Escape405.58 Inlet Connector Assembly406.27 Inlet Filter (with ‘O’ seal tted)416.38 Clamp Bracket (Inlet)416.41 Thermal Switch4

25405.58406.27416.38416.41416.48416.51872.01872.281563.5071563.539AAAAAAAAAA1563.6941563.534BB1563.5191563.5441563.5451563.5331563.5371563.538CCCCC156

26Dimensions90 mm79 mm207 mm340 mm348 mm

27Wiring DiagramThermal CutoutDual DiscTank ConnectionLoadInlet ConnectorPressure/Power Selector SwitchSolenoid ValveLow Flow NeonPower On NeonSTART/S

28Notes

29Notes

3IntroductionThank you for purchasing a quality Mira product. To enjoy the full potential of your new product, please take time to read this guide tho

30Notes

31Customer ServicesSpare PartsWe maintain an extensive stock of spares, and aim to have functional parts available for ten years from the date of nal

321060688-W2-C (1563) (J95G/H) © Kohler Mira Limited, April 2007Mira Showers Kohler Mira Ltd Cromwell Road, Cheltenham GL52 5EP.Mira is a registered

4Important Safety InformationInstallation must be carried out in accordance with these instructions, and must be conducted by designated, qualied and

52. Caution!2.1. Read all of these instructions and retain this guide for later use.2.2. The electrical installation must comply to “BS 7671 - Requ

6Pack Contents ChecklistMira Escape 3 x Wall Plugs 3 x Fixing Screws 1 x Mira Escape 1 x Compression Nut 1 x Olive 3 x Case InsertsTick the appropriat

7Specifications1. PlumbingMinimum maintained inlet pressure 70 kPa (0.7 bar).100 kPa (1.0 bar) recommended for satisfactory operation.Maximum static i

8Avoid layouts where the shower hose will be sharply kinked. This may reduce the life of the hose.A Soap Dish/Hose Retaining Ring is supplied to preve

92. ElectricalIn a domestic installation, the rating of the electricity supplier’s fuse and the consumer unit must be adequate for the additional dema